§32904. Calculation of average fuel economy
(a)
(A) section 32902(a) of this title in a way prescribed by the Administrator; and
(B) section 32902(b)–(d) of this title by dividing-
(i) the number of passenger automobiles manufactured by the manufacturer in a model year; by
(ii) the sum of the fractions obtained by dividing the number of passenger automobiles of each model manufactured by the manufacturer in that model year by the fuel economy measured for that model.
(2)(A) In this paragraph, "electric vehicle" means a vehicle powered primarily by an electric motor drawing electrical current from a portable source.
(B) If a manufacturer manufactures an electric vehicle, the Administrator shall include in the calculation of average fuel economy under paragraph (1) of this subsection equivalent petroleum based fuel economy values determined by the Secretary of Energy for various classes of electric vehicles. The Secretary shall review those values each year and determine and propose necessary revisions based on the following factors:
(i) the approximate electrical energy efficiency of the vehicle, considering the kind of vehicle and the mission and weight of the vehicle.
(ii) the national average electrical generation and transmission efficiencies.
(iii) the need of the United States to conserve all forms of energy and the relative scarcity and value to the United States of all fuel used to generate electricity.
(iv) the specific patterns of use of electric vehicles compared to petroleum-fueled vehicles.
(b)
(i) passenger automobiles manufactured domestically by a manufacturer (or included in this category under paragraph (5) of this subsection); and
(ii) passenger automobiles not manufactured domestically by that manufacturer (or excluded from this category under paragraph (5) of this subsection).
(B) Passenger automobiles described in subparagraph (A)(i) and (ii) of this paragraph are deemed to be manufactured by separate manufacturers under this chapter, except for the purposes of section 32903.
(2) In this subsection (except as provided in paragraph (3)), a passenger automobile is deemed to be manufactured domestically in a model year if at least 75 percent of the cost to the manufacturer is attributable to value added in the United States or Canada, unless the assembly of the automobile is completed in Canada and the automobile is imported into the United States more than 30 days after the end of the model year.
(3)(A) In this subsection, a passenger automobile is deemed to be manufactured domestically in a model year, as provided in subparagraph (B) of this paragraph, if at least 75 percent of the cost to the manufacturer is attributable to value added in the United States, Canada, or Mexico, unless the assembly of the automobile is completed in Canada or Mexico and the automobile is imported into the United States more than 30 days after the end of the model year.
(B) Subparagraph (A) of this paragraph applies to automobiles manufactured by a manufacturer and sold in the United States, regardless of the place of assembly, as follows:
(i) A manufacturer that began assembling automobiles in Mexico before model year 1992 may elect, during the period from January 1, 1997, through January 1, 2004, to have subparagraph (A) of this paragraph apply to all automobiles manufactured by that manufacturer beginning with the model year that begins after the date of the election.
(ii) For a manufacturer that began assembling automobiles in Mexico after model year 1991, subparagraph (A) of this paragraph applies to all automobiles manufactured by that manufacturer beginning with the model year that begins after January 1, 1994, or the model year beginning after the date the manufacturer begins assembling automobiles in Mexico, whichever is later.
(iii) A manufacturer not described in clause (i) or (ii) of this subparagraph that assembles automobiles in the United States or Canada, but not in Mexico, may elect, during the period from January 1, 1997, through January 1, 2004, to have subparagraph (A) of this paragraph apply to all automobiles manufactured by that manufacturer beginning with the model year that begins after the date of the election. However, if the manufacturer begins assembling automobiles in Mexico before making an election under this subparagraph, this clause does not apply, and the manufacturer is subject to clause (ii) of this subparagraph.
(iv) For a manufacturer that does not assemble automobiles in the United States, Canada, or Mexico, subparagraph (A) of this paragraph applies to all automobiles manufactured by that manufacturer beginning with the model year that begins after January 1, 1994.
(v) For a manufacturer described in clause (i) or (iii) of this subparagraph that does not make an election within the specified period, subparagraph (A) of this paragraph applies to all automobiles manufactured by that manufacturer beginning with the model year that begins after January 1, 2004.
(C) The Secretary of Transportation shall prescribe reasonable procedures for elections under subparagraph (B) of this paragraph.
(4) In this subsection, the fuel economy of a passenger automobile that is not manufactured domestically is deemed to be equal to the average fuel economy of all passenger automobiles manufactured by the same manufacturer that are not manufactured domestically.
(5)(A) A manufacturer may submit to the Secretary of Transportation for approval a plan, including supporting material, stating the actions and the deadlines for taking the actions, that will ensure that the model or models referred to in subparagraph (B) of this paragraph will be manufactured domestically before the end of the 4th model year covered by the plan. The Secretary promptly shall consider and act on the plan. The Secretary shall approve the plan unless-
(i) the Secretary finds that the plan is inadequate to meet the requirements of this paragraph; or
(ii) the manufacturer previously has submitted a plan approved by the Secretary under this paragraph.
(B) If the plan is approved, the Administrator shall include under paragraph (1)(A)(i) and exclude under paragraph (1)(A)(ii) of this subsection, for each of the 4 model years covered by the plan, not more than 150,000 passenger automobiles manufactured by that manufacturer but not qualifying as domestically manufactured if-
(i) the model or models involved previously have not been manufactured domestically;
(ii) at least 50 percent of the cost to the manufacturer of each of the automobiles is attributable to value added in the United States or Canada;
(iii) the automobiles, if their assembly was completed in Canada, are imported into the United States not later than 30 days after the end of the model year; and
(iv) the model or models are manufactured domestically before the end of the 4th model year covered by the plan.
(c)
(d)
(e)
(
| Revised Section | Source (U.S. Code) | Source (Statutes at Large) |
|---|---|---|
| 32904(a)(1) | 15:2003(a)(1), (2). | Oct. 20, 1972,
|
| 32904(a)(2) | 15:2003(a)(3). | Oct. 20, 1972,
|
| 32904(b)(1) | 15:2003(b)(2). | Oct. 20, 1972,
|
| 32904(b)(2) | 15:2003(b)(1). | |
| 32904(b)(3) | 15:2003(b)(4). | Oct. 20, 1972,
|
| 32904(b) (4)–(6) | 15:2003(b)(3). | Oct. 20, 1972,
|
| 32904(c) | 15:2003(d)(1) (1st–3d sentences), (2), (e). | |
| 32904(d) | 15:2003(d)(3). | |
| 32904(e) | 15:2003(d)(1) (last sentence), (f). |
In subsection (a)(1), before clause (A), the words "of a manufacturer subject to" are substituted for "for the purposes of" for clarity. In clause (B)(ii), the words "the sum of the fractions obtained by" are substituted for "a sum of terms, each term of which is a fraction created by" to eliminate unnecessary words.
Subsection (a)(2)(A) is substituted for "as defined in section 2012(b)(2) of this title" for clarity.
In subsection (a)(2)(B), before clause (i), the words "the Administrator shall include in the calculation of average fuel economy" are substituted for "the average fuel economy will be calculated . . . to include" for clarity. The text of 15:2003(a)(3)(B) is omitted as executed. The words "determine and propose" are substituted for "propose" for clarity and consistency with the authority of the Secretary under the source provisions. The words "based on the following factors" are substituted for "Determination of these fuel economy values will take into account the following parameters" for clarity and to eliminate unnecessary words. The factors in clauses (i)–(iv) are applied to revisions in fuel economy values for clarity and consistency with the authority of the Secretary under the source provisions. In clause (iv), the words "patterns of use" are substituted for "driving patterns" for clarity.
In subsection (b)(1), before clause (A), the text of 15:2003(b)(2)(A)–(D) is omitted as executed. In clause (A), the words "is imported . . . more than 30 days after" are substituted for "is not imported . . . prior to the expiration of 30 days following" for clarity and for consistency in the revised chapter. The words "The EPA Administrator may prescribe rules for purposes of carrying out this subparagraph" are omitted as surplus because of the authority of the Administrator to prescribe regulations under section 32910(d) of the revised title. The term "regulations" is used in section 32910(d) instead of "rules" for consistency in the revised title and because the terms are synonymous. In clause (B), the words "which is imported by a manufacturer in model year 1978 or any subsequent year, as the case may be, and" are omitted as surplus.
In subsection (b)(2)(A), before clause (i), the words "Except as provided in paragraphs (4) and (5) of this subsection" are added for clarity. The words "the Administrator shall make separate calculations" are substituted for "In calculating average fuel economy . . . the EPA Administrator shall separate the total number of passenger automobiles manufactured by a manufacturer into the following two categories" and "The EPA Administrator shall calculate the average fuel economy of each such separate category" to eliminate unnecessary words. In clauses (i) and (ii), the reference in the parenthetical to paragraph (3) is substituted for the reference in the source to paragraph (3), which apparently should have been a reference to paragraph (4). The text of 15:2003(b)(1)(A) (words in parentheses) and (B) (words in parentheses) is omitted as executed.
Subsection (b)(2)(B) is substituted for 15:2003(b)(1) (words after last comma) because of the restatement.
In subsection (b)(3)(A), before clause (i), the word "deadlines" is substituted for "dates" for clarity. The text of 15:2003(b)(4)(C) is omitted as executed.
In subsection (b)(4)(A), before clause (i), the words "A manufacturer may file with the Secretary of Transportation a petition for an exemption from the requirement of separate calculations under paragraph (2)(A) of this subsection" are substituted for "petition . . . for an exemption from the provisions of paragraph (1) filed by a manufacturer, the Secretary" for clarity.
In subsection (b)(5)(B), the words "judgment of the court under this subparagraph may be reviewed" are substituted for "judgment of the court affirming, remanding, or setting aside, in whole or in part, any such decision shall be final, subject to review" to eliminate unnecessary words.
In subsection (b)(5)(C), the words "Notwithstanding any other provision of law" are omitted as surplus. The words "a petition for" are added for consistency.
In subsection (c), the words "of a model type" and "of a manufacturer" are omitted as surplus. The words "by rule" are omitted as surplus because of the authority of the Administrator to prescribe regulations under section 32910(d) of the revised title. The term "regulations" is used in section 32910(d) instead of "rules" for consistency in the revised title and because the terms are synonymous. The words "However . . . the Administrator shall use the same procedures for passenger automobiles the Administrator used" are substituted for "Procedures so established with respect to passenger automobiles . . . shall be the procedures utilized by the EPA Administrator" for clarity. The words "(in accordance with rules of the EPA Administrator)" are omitted as surplus. The words "fuel economy tests shall be carried out with" are substituted for "Procedures under this subsection . . . shall require that fuel economy tests be conducted in conjunction with" to eliminate unnecessary words.
In subsection (d), the words "The Administrator shall prescribe a procedure under this section, or an amendment . . . at least" are substituted for "Testing and calculation procedures applicable to a model year and any amendment to such procedures . . . shall be promulgated not less than" to eliminate unnecessary words.
In subsection (e), the words "his duties under" are omitted as surplus.
Pub. L. 103–429, §6(36)(A)
This makes conforming amendments necessary because of the restatement of 15:2003(b)(2)(G) as 49:32904(b)(3) by section 6(36)(B) of the bill.
| Revised Section | Source (U.S. Code) | Source (Statutes at Large) |
|---|---|---|
| 32904(b) | 15:2003(b)(2)(E), (G). | Oct. 20, 1972, |
The text of 49:32904(b)(1) is the text of 49:32904(b)(2), as enacted by section 1 of the Act of July 5, 1994 (
The text of subsection (b)(2) is the text of 49:32904(b)(1)(A), as enacted by section 1 of the Act of July 5, 1994 (
In subsection (b)(3)(A), the words "is imported . . . more than 30 days after" are substituted for "is not imported . . . prior to the expiration of 30 days following" for clarity and consistency with title 49, United States Code.
In subsection (b)(3)(C), the words "and the EPA Administrator may prescribe rules for purposes of carrying out this subparagraph" are omitted as surplus because of the authority of the Administrator to prescribe regulations under 49:32910(d). The amendment made by section 371(b)(2) of the North American Free Trade Implementation Act (
The text of subsection (b)(4) is the text of 49:32904(b)(1)(B), as enacted by section 1 of the Act of July 5, 1994 (
Pub. L. 103–429, §6(36)(C), (D)
This makes conforming amendments necessary because of the restatement of 15:2003(b)(2)(G) as 49:32904(b)(3) by section 6(36)(B) of the bill.
Editorial Notes
Amendments
2007-Subsec. (b)(1)(B).
Subsec. (b)(6) to (8).
1996-Subsec. (b)(6)(C).
1994-Subsec. (b)(1).
"(A) a passenger automobile is deemed to be manufactured domestically in a model year if at least 75 percent of the cost to the manufacturer is attributable to value added in the United States or Canada, unless the assembly of the automobile is completed in Canada and the automobile is imported into the United States more than 30 days after the end of the model year; and
"(B) the fuel economy of a passenger automobile that is not manufactured domestically is deemed to be equal to the average fuel economy of all passenger automobiles manufactured by the same manufacturer that are not manufactured domestically."
Subsec. (b)(2).
"(2)(A) Except as provided in paragraphs (4) and (5) of this subsection, the Administrator shall make separate calculations under subsection (a)(1)(B) of this section for-
"(i) passenger automobiles manufactured domestically by a manufacturer (or included in this category under paragraph (3) of this subsection); and
"(ii) passenger automobiles not manufactured domestically by that manufacturer (or excluded from this category under paragraph (3) of this subsection).
"(B) Passenger automobiles described in subparagraph (A)(i) and (ii) of this paragraph are deemed to be manufactured by separate manufacturers under this chapter."
Subsec. (b)(3), (4).
Subsec. (b)(5).
Subsec. (b)(5)(B).
Subsec. (b)(6).
Subsec. (b)(6)(A).
Subsec. (b)(7), (8).
Statutory Notes and Related Subsidiaries
Effective Date of 2007 Amendment
Amendment by
Effect of Repeal on Existing Exemptions
"(b)
"(c)